Influence of accelerated curing on the compressive strength of polymer-modified concrete

In recent building practice, rapid construction is one of the principal requisites. Furthermore, in designing concrete structures, compressive strength is the most significant of all parameters. While 3-d and 7-d compressive strength reflects the strengths at early phases, the ultimate strength is paramount. An effort has been made in this study to develop mathematical models for predicting compressive strength of concrete incorporating ethylene vinyl acetate (EVA) at the later phases. Kolmogorov-Smirnov (KS) goodness-of-fit test was used to examine distribution of the data. The compressive strength of EVA-modified concrete was studied by incorporating various concentrations of EVA as an admixture and by testing at ages of 28, 56, 90, 120, 210, and 365 d. An accelerated compressive strength at 3.5 hours was considered as a reference strength on the basis of which all the specified strengths were predicted by means of linear regression fit. Based on the results of KS goodness-of-fit test, it was concluded that KS test statistics value (D) in each case was lower than the critical value 0.521 for a significance level of 0.05, which demonstrated that the data was normally distributed. Based on the results of compressive strength test, it was concluded that the strength of EVA-modified specimens increased at all ages and the optimum dosage of EVA was achieved at 16% concentration. Furthermore, it was concluded that predicted compressive strength values lies within a 6% difference from the actual strength values for all the mixes, which indicates the practicability of the regression equations. This research work may help in understanding the role of EVA as a viable material in polymer-based cement composites.     

Performance evaluation of structural concrete using controlled quality coarse and fine recycled concrete aggregate

This paper presents the fresh, mechanical, and durability performance, of a structural concrete mix classified as C-1, by the Canadian Standards Association (CSA) made with controlled quality Recycled Concrete Aggregate (RCA). Five mixes with water-to-cementing material (w/cm) ratio of 0.40 were produced with various RCA contents and tested against two 0% RCA control mixes made with General Use (GU) cement, and General Use Limestone cement (GUL). The RCA contents in the mixes were 10%, 20%, and 30% by coarse aggregate volume replacement, as well as 10% and 20% fine and coarse (granular) aggregate volume replacement. All evaluated mixes met the specifications from the CSA for fresh, mechanical, and durability properties. The coarse RCA mixes performed better than the granular RCA mixes in terms of flexural and splitting tensile strengths, linear drying shrinkage, water sorptivity, and rapid chloride-ion permeability, where the test results were significantly affected by the ultra fines present in the granular RCA.     

大宗粉煤灰的综合利用及提质方案

对于大宗粉煤灰原灰进行分选加球磨机粉磨，同时添加合适的激发剂进行提质，可以生产出不同细度和活性的粉煤灰产品，提升粉煤灰在水泥及商品砼中的用量。介绍了某发电公司的粉煤灰处置现状，在此基础上，对商品砼的粉煤灰性能要求进行了大量市场调研，针对性地给出了该公司粉煤灰的提质方案，最后进行了提质粉煤灰的应用市场和产品竞争力分析。     

Stress distribution in thick-walled cylinder due to non-uniform radial pressure on the example of reinforcement corrosion in concrete

This paper presents an analytical solution to the non-uniform pressure on thick-walled cylinder. The formulation is based on the linear elasticity theory (plain strain) and stress function method. As an example, the proposed solution is used to model the stress distribution due to non-uniform steel reinforcement corrosion in concrete. The model is formulated considering different scenarios of corrosion pressure distribution. It is validated against the finite element model for different cases of non-uniform pressure distributions. The results show that the corrosion-induced cracks are likely to start just beyond the anodic zone. This is confirmed by the experimental tests on concrete cylinder exposed to non-uniform accelerated corrosion of steel reinforcement. The model can be effectively used to calculate the distribution of corrosion-induced stresses in concrete.     

Effect of steel slag on 3D concrete printing of geopolymer with quaternary binders

A new type of 3D-printable ‘one-part’ geopolymer was synthesized with fly ash (FA), granulated blast furnace slag (GBFS), steel slag (SS) and flue gas desulfurization gypsum (FGD). The effects of SS content (0–40%) on the rheological properties, 3D-printability, mechanical anisotropy and reaction kinetics of geopolymer were investigated. The yield stress and plastic viscosity monotonically decreased with the increasing SS content. Contrarily, the geopolymer with 10% of SS presented better extrudability, buildability and mechanical strength than those with 0, 20%, 30% and 40% of SS. This was mainly attributed to the conflicting influence of SS on geopolymerization, of which the OH^? produced by hydration of SS raised the alkalinity of the reaction system and accelerated the dissolution of SiO₄^4? and AlO₄^5?, while the low reactivity prohibited the following polymerization process. Furthermore, the 3D-printed geopolymer presented more compact microstructure and less mechanical anisotropy thanks to the crosslinking of morphologically complementary products, including N(C)-A-S-H, C–S–H, AFt and CH, formed via synergistic reaction of FA-GBFS-SS-FGD system.     

混凝土结构的压电声波检测分析

本文介绍了混凝土结构的压电体波和表面波检测的主要进展,对两种压电声波检测的优缺点进行了总结。体波检测设备一般埋入混凝土内部,需要选择合理的检测部位,检测结果较为精确;声表面波检测无需选择特定的部位,但是检测深度有限。在实际检测工作过程中,可以联合两种方法相互验证。     

人工砂混凝土性能试验研究

采用正交试验方法配制了不同人工砂取代率、石粉含量、粉煤灰含量的混凝土, 对比了每组混凝土的坍落度, 研究了3 d、28 d龄期混凝土的抗压性能。结果表明: 最优配比的人工砂取代率、石粉含量和粉煤灰含量分别为10%、3%和5%, 此时28 d抗压强度为40.1 MPa, 满足30 MPa的混凝土设计强度。     

超高性能混凝土国内外研究与应用进展*

介绍了超高性能混凝土（UHPC）的制备原理和性能特点，对UHPC国内外研究和应用情况进行了综述，指出了我国UHPC研究和应用中存在的问题。结果表明：UHPC是一种具有优异的力学性能、耐久性能和环保效益的新型水泥基复合材料。国外在UHPC理论研究和应用研究方面都取得了大量成果，在实际工程中已经获得了广泛的应用；近年来我国在理论研究和应用方面也得到了快速发展；如何简化UHPC制备工艺、降低生产成本、补偿自收缩是今后的主要研究方向，完善相关规范标准以更好地指导UHPC现浇工程应用是目前首要解决的问题。随着环保和可持续发展理念的日益重视，UHPC这种低碳环保材料将有广阔的发展前景。     

Investigation on the effectiveness of the repair method 8.3 “Corrosion protection by increasing the electrical resistivity” in chloride-containing concrete Part 2: Chloride redistribution in concrete after application of a system sealing surface protective coating

This DFG-funded research project aimed to gain a better understanding of the mechanisms of the W-Cl repair principle within the framework of fundamental investigations, to contribute to the creation of the necessary basis for a broader application of the repair principle in practice. The focus was on the development of a model to describe the chloride redistribution after the application of a system sealing surface protective coating. On the basis of Fick's second law of diffusion, a mathematical model with a self-contained analytical solution was developed, with the help of which the chloride redistribution after application of a system sealing surface protective coating can be calculated under the idealized assumption of complete water saturation of the concrete. Furthermore, the influence of the dehydration of the concrete, expected as a result of the application of the repair principle W-Cl, on the chloride redistribution was investigated. On the basis of laboratory tests and numerical simulations, material-specific reduction functions were developed to quantify the relationship between the chloride diffusion coefficient and the ambient humidity.     

复杂膨胀性围岩条件下交岔点支护技术研究

针对复杂膨胀性围岩条件下交岔点高应力集中区围岩稳定性控制和支护技术难题，通过对交岔点围岩变形表现形式、交岔点围岩变形机理的研究分析，提出了交岔点支护难点及重点。基于围岩控制理论分析，提出了“有限让压的柔性支护+全断面封闭抗压的刚性支护技术”，前期柔性支护采用“高强、高预应力锚杆+锚索+喷浆”联合支护有限度控制围岩变形，允许围岩在可控范围内释放围岩应力|后期通过架设异形支架与支撑架组成的联合支护体并喷射混凝土对交岔点围岩进行全断面封闭抗压支护，有效控制巷道交岔点围岩的变形。确保了交岔点围岩变形的整体可控性、稳定性，达到了预期支护效果。